3G3FV MANUAL PDF

procedures for installing and wiring the SYSDRIVE 3G3FV-j-CUE/EF3HV-j-CUE Please read this manual thoroughly and handle and operate the product with. The SYSDRIVE 3G3FV is OMRON’s new special-purpose inverter. It provides the harmony between performance, versatility, and simplicity. Using a unique. Manuals and User Guides for Omron SYSDRIVE 3G3FV. We have 1 Omron SYSDRIVE 3G3FV manual available for free PDF download: User Manual.

Author: Zubei Doura
Country: Ecuador
Language: English (Spanish)
Genre: Politics
Published (Last): 8 November 2005
Pages: 306
PDF File Size: 5.45 Mb
ePub File Size: 9.98 Mb
ISBN: 648-8-75526-772-7
Downloads: 85077
Price: Free* [*Free Regsitration Required]
Uploader: Yozshugis

A total of 21 types of Inverters are available for maximum applicable motor capacities of 0. Chapter 6 Advanced Operation The sign bit is used as a data bit, so only positive plus data can be set.

The acceleration time C is a parameter in program mode.

Run commands are ignored during deceleration time. This setting is used as a basis for motor protection Valid access levels Parameter If 1 is set, the final gain will be equal mnual the result of multiplication by the set value of H Any one of the four values monitored at startup frequency reference, output frequency, output current, or the value set in parameter o can mannual selected to appear when the power is turned on.

Main Circuit Terminals Checking The Accessories To print the manual completely, please, download it. Operator Parameter Lists It is recommended that a Noise Filter be 3h3fv at the Power Supply to minimize this noise transmission. Chapter 4 Trial Operation Auto-tuning Auto-tuning Operation Execute auto-tuning and the motor parameters are set automatically.

  BACH BOURREE IN E MINOR PDF

OMRON SYSDRIVE 3G3FV Series Inverters

The operation mode display will appear. Set values 4 to 7. Chapter 5 Basic Operation Note 2. Sets the motor rated current.

Auto-tuning Chapter 4 Trial Operation Auto-tuning Auto-tuning Operation Execute auto-tuning and the motor parameters are set automatically. Disabling Reverse Operation b Motor acceleration fault The torque limit function is operating.

Chapter 8 Maintenance Operations Troubleshooting Due to parameter setting errors, faulty wiring, and so on, the Inverter and motor may not operate as expected when the system is started up.

Tighten the screws to a tightening torque of 0. manuual

Omron SYSDRIVE 3G3FV Manuals

Parameter F sets the length of time that the difference between the motor speed and reference speed must exceed the PG speed deviation detection level in order to generate a PG speed deviation fault DEV.

Wiring and Connection Connect to the power supply and peripheral devices. 3gg3fv value Gain Max. Select the type that fits the application and control method. When the forward torque limit has been set, the analog input signal acts as the limit value for torque generated in the forward direction. Otherwise, ventilation will be affected, 3g3vf the Inverter to overheat. Page Chapter 6 Advanced Operation Unlike other parameter settings, the external fault settings have an input procedure, as shown in the following diagrams.

If this occurs, insert a diode as indicated by section A below. Installation Conditions Chapter 2 Installation Two, 4 dia.

Protective And Diagnostic Functions Chapter 6 Advanced Operation Note When the S-curve characteristic time is set, the acceleration and deceleration times will be lengthened as follows: Table Of Contents About this Manual This manual is divided into the chapters described in the following table.

  2SC1384 DATASHEET PDF

Chapter 6 Advanced Operation Parameters b and b cannot be changed during operation. Standard fan-cooled motor 0 to manuql Comments to this Manuals Your Name. Chapter 2 Installation Countermeasures Against Induction Noise As described previously, a noise filter can be used to prevent induction noise from being generated on the output side. After initialization the access level is set to Quick-start A In that case, use a higher rank Inverter with parameter L set to 0 and parameter L set to 1.

These parameters can- not be changed during operation. If the setting is increased too much, the current can fall to the point where stalling occurs. Deceleration time set in b Double the values for V class Inverters. Set the parameter if stable slip compensation is required in the constant output area where the operating frequency is 3b3fv high as or higher than the rated frequency.

Page Chapter manuak Basic Operation Note 1. Chapter 2 Installation H Protecting Inverter from Foreign Matter During Installation Place a cover over the Inverter during installation to shield it from metal power produced by drilling.