HEATHKIT SA-2060 MANUAL PDF

HEATHKIT. MANUAL for the. DELUXE. ANTENNA TUNER. Model SAA You must deliver the unit at your expense to the Heath factory, any Heathkit. View and Download Heath Kit SAA manual online. Heathkit SAA TV Antenna pdf manual download. Antenna Tuner SA Amateur-D Heathkit Brand, Heath Co.; Benton Harbor Select picture or schematic to display from thumbnails on the right and click for.

Author: Akinojinn Juzragore
Country: Samoa
Language: English (Spanish)
Genre: Video
Published (Last): 10 April 2016
Pages: 254
PDF File Size: 16.24 Mb
ePub File Size: 2.93 Mb
ISBN: 787-5-85710-151-7
Downloads: 49492
Price: Free* [*Free Regsitration Required]
Uploader: Yozshutilar

Just start the nut onto the end of the screw; it will be tightened later.

Before you proceed, haethkit sure you connect your transmitting equipment maunal shown in Pictorial An easy way to do this is to hook the folded end of the wire around a door knob or similar object and then pull the wire until it is tight, Fold the foot wire in the middle. NOT COVERED — The correction of assembly errors, adjustments, calibration, and damage due to misuse, abuse or negligence are not covered by s-a2060 warranty Use of corrosive solder and ‘or the unauihorized modification of the product or of any furnished componen.

Parts Replacement Retain original parts until you receive replacements. Slide a 10 flat fiber washer onto the end of each threaded rod. Be sure the edges of the counter are parallel to the edges of the bracket before you tighten the screws.

Be careful not to cut into the inner wire insulation when you cut the outer insulation. This completes the assembly of the roller inductor. When solder tends to “ball” or does not stick to the tip, the tip needs to be cleaned and retinned. Now tighten the control nut at BC. This will make sure the top edge of the ceramic insulator plate is flush manuxl the top edge of the capacitor front plate. It is best to ground all equipment to one point at the operating position; then ground this point as discussed above.

  IMMORTALITY OR RESURRECTION BY SAMUELE BACCHIOCCHI PDF

Connect the hook on the free end of the spiral shield to solder lug K NS. The antenna you use should be insulated along its entire janual from any contact with any parts sa-20600 buildings, trees, etc.

Then install the setscrew in hole AS.

HEATH KIT SAA MANUAL Pdf Download.

F ceramic capacitor to SW3 lug 4 S-l. Set one of the nylon gears, the shaft collar, manuzl the four shaft couplers aside until they are called for in a step. Always use the matching setting that uses the most capaci- tance hezthkit Cl and C2, as maximum capacitance pro- vides the best harmonic attenuation.

Loosen the setscrews in the knob and remove the knob from the shaft. Then push the end of the sensor cable into grommet A and pull the cable through to take up all the slack. Follow the instructions carefully.

Refer to Detail 1-lD and work the center por- tions of the three feedthrough insulators into holes B, C, and D, Then place a fiber washer, a female ceramic element, a flat washer and a nut onto each feedthrough stud.

As you slide the stepped coupler to- ward the inductor shaft, slide the gear on the inductor shaft forward until the two gears heathoit equally meshed.

Heath kit SA-2060A Manual

You no longer need to connect and disconnect feed lines to load your transmitter into the dummy load. I 17 Sa-22060 28 Heathkif Locate the following parts: Detail B Slide the hwathkit rearward and line up its mounting holes with those in the chassis, Hold the inductor in place. Depress the three switch pushbuttons to their “in” positions. Note the dotted outline on the Pictorial.

Connect this ground post to a good earth ground or a water pipe.

At the rear of roller inductor Ll, hook your middle and index fingers over the two straps going to matching capacitors Cl and C2. Check the equipment to see that all screws and parts are secured.

  HIDRONEFROSE CAUSAS PDF

With a single switch you may select a dummy load, or any of three permanently-connected antennas, in- cluding a long-wire antenna. Pull on the ends of the shield and stretch it evenly to a length of 26″. Push one of the knobs onto the capacitor shaft. Place a flat washer, the male ceramic element, and a fiber washer on the stud.

Refer to Detail A and cut and separate the in- dividual wire ends, using diagonal cutters, at one end of the 8-conductor cable. Grasp the shaft coupler and turn the shaft to the second of the four switch positions. Remove the paper backing from the blue and white label and press the label in place on the inside of the rear panel in the upper right corner as shown.

Remove and discard the shorting wires from the meter terminals. Before you use a water pipe ground, inspect the con- nection around your water meter. Then tighten the lug hardware, if this has not already been done.

Use nuts and 10 flat fiber washers to secure the assembly. Then slide the spring washer on the rear shaft of the roller inductor with the curved side of the spring washer toward the inductor, Apply grease to the rear shaft end of roller in- ductor. Set the knob aside temporarily.

Refer to Detail D and position either fiberglass shaft into front panel bushing S. Also, hold this side of the front plate against a flat surface when you tighten the screws. Then, working from the center outward in both directions, smooth the label firmly onto the front panel.

Detail C Place the sensor assembly close to the rear of the chassis.